MODIFICATION OF SURFACE, PHYSICAL AND CHEMICAL PROPERTIES OF ACTIVATED CARBONS FOR WATER PURIFICATION

This study, “MODIFICATION OF SURFACE, PHYSICAL AND CHEMICAL PROPERTIES OF ACTIVATED CARBONS FOR WATER PURIFICATION” contains concise information that will serve as a framework or guide for your project work. The project study is well-researched for academic purposes and are usually provided in complete chapters with adequate References.

Keywords: MODIFICATION OF SURFACE, PHYSICAL AND CHEMICAL PROPERTIES OF ACTIVATED CARBONS FOR WATER PURIFICATION

ABSTRACT
The purpose of this work was to study the effect of chemical surface properties of activated carbons for their use in water purification. To achieve this objective, activated carbon in both granular and powdered forms namely: as received and devolatilized carbons were prepared. Proximate analysis of the carbon materials was performed. Mass titration experiments were carried out to determine the point of zero charge of the activated carbon materials. Again, using an ultraviolet spectrophotometer, the adsorption of phenol on as-received and devolatilized activated carbon was investigated. Adsorption isotherms were acquired from which the monolayer adsorption capacities were calculated.

CHAPTER ONE
INTRODUCTION
1.1 ORIGIN AND NATURE OF ACTIVATED CARBON
Carbon is the fifteenth most abundant element in the earth’s crust and the fourth most abundant element in the universe by mass after hydrogen, helium and oxygen. Scientists, industries, and consumers use different forms of carbon and carbon containing compounds in many ways such as activated carbon or carbon in its active form which can be used to purify water, among others.
Activated carbon is a form of carbon that has been produced to make it extremely porous and thus have a very large surface area available for adsorption or chemical reactions.
It can be defined as a microcrystalline non-graphitic amorphous form of carbon which has been processed to develop a high internal porosity due to its network of inter-connecting pores.
The history of activated carbon is dated since the fifteenth century, during the time of Columbus when sailors used to blacken the inside of wooden water barrels with fire, since they observed that the water would stay fresh much longer. It is likely that people at that time proceeded by intuition only without having any
insight into the mechanism of the effect. The mechanism was recognized beginning from the eighteenth century.
In 1862, Lipscombe prepared a carbon material for purifying portable water. This development paved the way for the commercial application of activated carbon first for portable water and then in waste water sector.

1.2 METHODS OF MANUFACTURE OF ACTIVATED CARBON
The methods employed in the industrial manufacture of activated carbons are numerous but consist of three main methods namely; Chemical activation, Steam activation and thermal processing techniques.
The raw materials or precursors used in the manufacture of activated carbon are as follows; Softwood, coconut shell, lignite, hardwood, grain and agro products, bituminous coal, anthracite, etc.
Chemical activation is generally used for the production of activated carbon from sawdust, wood or peat and uses chemicals for activation. Chemical activation technique involves mixing an inorganic chemical compound with the carbonaceous raw materials and the most widely used activating agents are Phosphoric acid and Zinc Chloride.
Steam activation technique is generally used for coal-based, coconut shell and grain-based activated carbons and uses gases, vapors or a mixture of both for its activation.
Thermal processing technique is a separation process that removes unwanted materials from the carbonaceous precursor used under varying heat applications. This technique is at a lower cost compared to the two techniques above and meets all environmental standards, while others need expensive solutions to achieve the same results.

1.3 NEED FOR PRESENT INVESTIGATION
The need for present investigation of this material cannot be over emphasized. This is as a result of the pressing need for treatment of waste water emanating from domestic and industrial concerns.
Activated carbon plays an important role in the purification of fluids (water), including vegetable oils used in domestic cooking and as a precursor in industrial manufacture of food products. The slow pace of technological development in the country has resulted to the expenditure of the nation’s resources on importation of activated carbons to meet the demand for local chemical and process industries, as well as the demand for municipal and industrial water treatment plants.

Keywords: MODIFICATION OF SURFACE, PHYSICAL AND CHEMICAL PROPERTIES OF ACTIVATED CARBONS FOR WATER PURIFICATION

DO YOU WANT TO ORDER FOR THE COMPLETE PROJECT MATERIAL? Then click here

GET COMPLETE PROJECT

Have you made payment for this project? If YES, contact our Customer Care.

For further enquiries, call our Hotlines ☎: 08139342394 or 08152487601

PROJECT TOPICS AND MATERIALS | HIRE A WRITER | HOW TO PAY FOR PROJECT

Keywords: MODIFICATION OF SURFACE, PHYSICAL AND CHEMICAL PROPERTIES OF ACTIVATED CARBONS FOR WATER PURIFICATION

DISCLAIMER: hiWriters.com.ng focus on attracting students and researchers to materials that can be used as guide, framework, and reference for their project work. All contents/materials on this website are for research purposes only and for no reason should you copy verbatim. This platform is not encouraging any form of plagiarism, neither are we advocating the use of the project materials for cheating. We strictly recommend that research project topics and materials ordered for should serve as a guide or framework only. The contents therein should be used to generate fresh ideas for your own research. Finally, hiWriters.com.ng will not be liable for any material used inappropriately.